Brocade Communications Systems 8 Installationsanleitung Seite 51
- Seite / 186
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Verifying the PID mode
Before connecting the device to the fabric, verify that the WWN-based persistent port identifier (PID)
feature on the device matches the other switches in the fabric. This parameter must be identical for all
switches in the fabric and is set using the configure command as shown in the following example:
switch:admin>configure
Configure...
Fabric parameters (yes, y, no, n): [no] y
Domain: (1..239) [1]
Enable a 256 Area Limit
(0 = No,
1 = Zero Based Area Assignment,
2 = Port Based Area Assignment): (0..2) [0] 1
WWN Based persistent PID (yes, y, no, n): [no] yes
<command output truncated>
You can check the PID setting using the configshow command as in the following example. You can
use the | grep -i pid qualifier to pinpoint the PID information.
switch:admin> configshow | grep -i pid
fabric.ops.mode.pidFormat:1
fabric.wwnPidMode:1
The 1 indicates that the WWN-based persistent PID feature is enabled. The default value is 0 for
disabled.
Determining installed software licenses
Depending on the vendor agreement, certain licenses are factory installed on the device. To determine
which licenses are enabled, use the licenseShow command.
swDir:admin> licenseshow
AAbbccDDeeFFeeGG:
Web license
Zoning license
Extended Fabric license
Fabric Watch license
Performance Monitor license
Trunking license
Security license
In this example, the license key is AAbbccDDeeFFeeGG. Keep a copy of the license key for reference.
The 64-bit chassis ID is required to obtain and activate licenses for the device. The chassis ID is
available through the licenseIdShow command. The licenseShow and licenseIdShow commands
must be entered on the active CP blade. Refer to the Fabric OS Administrator's Guide for more
information.
Installing transceivers and attaching cables
The following two sets of steps cover the installation of transceivers and cables for most SFPs and for
QSFPs.
For a list of qualified transceivers for FC16-64 and CR16-x blades, refer to Qualified transceivers for
FC16-64 and CR16-x blades. on page 52
Verifying the PID mode
Brocade DCX 8510-8 Backbone Hardware Installation Guide 51
53-1002180-10
- Brocade DCX 8510-8 1
- Backbone 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- About This Document 11
- What’s new in this document 12
- Product Overview 13
- Hardware components 14
- Port side view of the device 15
- Supported blades 17
- Chassis slots numbering 18
- Port numbering 18
- High availability 20
- Reliability 20
- Serviceability 21
- Software features 21
- Security 22
- Network manageability 22
- Device Installation 25
- Providing power to the device 29
- Cable management 29
- Possible ICL configurations 35
- Using Brocade 2 km LWL QSFPs 38
- Rack installation options 41
- Initial Configuration 43
- Configuring the IP addresses 46
- Customizing a switch name 47
- Customizing a chassis name 48
- Setting the domain ID 48
- Setting the date and time 49
- Synchronizing local time 50
- Verifying the PID mode 51
- Managing cables 54
- Powering off the chassis 56
- System Monitoring 57
- FC8-32E port blade LEDs 63
- FC8-48E port blade LEDs 64
- FC8-64 port blade LEDs 65
- FC16-32 port blade LEDs 66
- FC16-48 port blade LEDs 67
- FC16-64 port blade LEDs 68
- FCOE10-24 FCoE blade LEDs 69
- FS8-18 encryption blade LEDs 70
- FX8-24 extension blade LEDs 71
- ESD precautions 85
- Removing a chassis door 86
- Replacing a chassis door 87
- Removing a blade 90
- Replacing a blade 91
- Removing a filler panel 92
- Replacing a filler panel 93
- Faulty CP blade indicators 94
- Power-up procedure 96
- Power-down procedure 98
- Completing the replacement 102
- Time and items required 104
- 53-1002180-10 105
- Identifying power supplies 107
- Removing a power supply 107
- Replacing a power supply 108
- Removing a blower assembly 109
- Replacing a blower assembly 110
- Using the wwnrecover utility 111
- Hot-swap replacement 113
- Power-down replacement 114
- Items required 119
- Removing an SFP+ transceiver 119
- Replacing an SFP+ transceiver 120
- Removing an mSFP transceiver 121
- Replacing an mSFP transceiver 121
- Faulty chassis indicators 125
- Downloading the configuration 131
- Cable routing table 134
- Introduction 137
- Diagnostics 139
- Troubleshooting 140
- FS8-18 blade 143
- FX8-24 blade 143
- FCOE10-24 blade 145
- Port Numbering Templates 147
- 1. Blade power LED 151
- 2. Blade status LED 151
- 3. FC ports 24-47 151
- 4. FC ports 0-23 151
- 1. 10-GbE CEE ports 12-23 156
- 2. 10-GbE CEE ports 0-11 156
- 3. Power LED 156
- 4. Status LED 156
- 2. Smart card port 157
- 3. Fibre Channel ports 0-15 157
- Regulatory Statements 159
- China ROHS 160
- FCC warning (US only) 160
- VCCI statement 161
- System specifications 163
- Fibre Channel 166
- Environmental requirements 169
- Power consumption (modules) 171
- Regulatory compliance (EMC) 174
- Caution and Danger Notices 177
- Danger Notices 178
- Electrical dangers 179
- WWN bezel 186
- WWN card 186
Verwandte Produkte und Handbücher für Eisen Brocade Communications Systems 8
(26 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.764 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern