Brocade-communications-systems Brocade MLX Series and Brocade Netlron XMR 53-1002 Bedienungsanleitung Seite 31
- Seite / 452
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 13
53-1002373-02
Hardware features
1
Brocade NetIron XMR routers
Brocade NetIron XMR Series routers are available in the following models:
• Brocade NetIron XMR 4000: 4 interface slots (see Figure 9 on page 13).
• Brocade NetIron XMR 8000: 8 interface slots (see Figure 10 on page 14).
• Brocade NetIron XMR 16000: 16 interface slots (see Figure 11 on page 15).
• Brocade NetIron XMR 32000: 32 interface slots (see Figure 12 on page 16).
The following sections described the components you can install in the router slots. For a detailed
list of components that ships with each router, refer to >>>>>>>>>>.
Brocade NetIron XMR 4000 router components
You can install the following components in the router slots:
• Up to two management modules (one active and one redundant).
• Up to three switch fabric modules.
• Up to four interface modules.
• Up to three power supplies (AC or DC).
Figure 9 displays the Brocade NetIron XMR 4000 router.
FIGURE 9 Brocade NetIron XMR 4000 router
1 Interface slot 2 4 ESD connector 7 Interface slot 3 10 Interface slot 4
2 Switch fabric slot 2 5 Interface slot 1 8 Management slot 1 11 -13 Three power supplies
installed in rear of
device
3 Switch fabric slot 3 6 Switch fabric slot 1 9 Management slot 2
7
6
5
1324
8910
11
12
13
- Brocade MLX Series and 1
- Brocade NetIron XMR 1
- Document History 2
- Contents 3
- 53-1002373-02 10
- About This Document 13
- Supported hardware 14
- What’s new in this document 14
- Document conventions 15
- Notice to the reader 16
- Related publications 16
- Getting technical help 17
- Product Overview 19
- Brocade MLXe routers 20
- • Up to 16 interface modules 22
- Hardware features 23
- Brocade MLXe-16 router 23
- • Up to 32 interface modules 24
- Brocade MLXe-32 router 25
- Brocade MLX routers 26
- FIGURE 6 Brocade MLX-8 router 27
- • Two management modules 29
- Brocade MLX-32 router 30
- Brocade NetIron XMR routers 31
- Router modules 35
- Part number Description 36
- Auxiliary flash slots 37
- External compact flash 37
- Console port 38
- 10/100/1000 Ethernet port 38
- Management module LEDs 39
- Interface modules 40
- Pwr Lnk/Act 43
- 8x10GE-X interface modules 45
- TABLE 7 8x10GE-X module LEDs 46
- LED Location State Meaning 47
- • Two LEDs per port 50
- Router type Number of Gen-2 51
- 10GX4-X interface 51
- Power supply requirements 51
- 3 TX RX 5 TX RX 7 TX RX 53
- • BR-MLX-1GCx24-X-ML 54
- • BR-MLX-1GCx24-X 54
- • 24 1 Gbps RJ45 copper ports 55
- • BR-MLX-1GFx24-X 56
- • BR-MLX-1GFx24-X-ML 56
- • 24 1 Gbps fiber ports 57
- Gbps fiber interface 58
- Position State Meaning 59
- LED Position State Meaning 59
- Router type Number of 61
- NI-MLX-1Gx48-T-A 61
- POS interface modules 62
- 2 Port 1 4 Port status LEDs 63
- 3 Port 2 6 Port 5 9 Port 8 64
- POS module LEDs 65
- Switch fabric modules 66
- Power supplies 68
- Rack mounting brackets 70
- 1 Fans in rear of chassis 71
- • Leave the fan speed as is 74
- • Increase the fan speed 74
- • Decrease the fan speed 74
- Supported software features 79
- FIGURE 48 Installing a module 94
- Module Slot number 101
- Brocade(config)# write memory 103
- Write startup-config done 103
- Connecting AC power 105
- Connecting DC power 105
- Final steps 107
- Brocade# set-fan-speed auto 112
- Current configuration: 112
- 1 AWG power supply wire: 117
- 1. Rail extender 121
- Installation requirements 129
- ATTENTION 131
- 2 10-32 x 5/8 inch screw 132
- 3 12-24 x 1/2 inch screw 132
- 4 M6 x 12 mm screw 132
- FIGURE 81 Saddle installation 133
- 2 Rack mounting poles 135
- 3Router mounting brackets 135
- Slide the chassis in the rack 139
- 1 Hooked tab 2 Stepped tab 144
- Figure 95 149
- Figure 97 151
- Accessing modules for service 152
- Cable management notes 153
- 4 ALM 9 Power supply 154
- 5 Latch handle open 154
- 2Power lug 157
- Activating the power source 159
- Verifying proper operation 160
- Displaying the module status 163
- Installation precautions 165
- Power precautions 167
- Installation considerations 169
- Installation procedure 169
- Brocade# config 170
- Brocade(config)# exit 170
- Brocade# write memory 170
- Brocade# reload 170
- Port covers 171
- Rear connector covers 171
- Caution: do not lift module 171
- Removing the shipping screws 173
- Interface modules 1 – 16 197
- 2Cord retainer 4 Ground point 206
- 2 Removable front panel 212
- Align the saddle in the rack 220
- Saddle installation 220
- Figure 146 226
- 1 Cable bundles 240
- Router LED states and actions 248
- General precautions 254
- 1 Front 3 Shipping screws 262
- 1 Standard 19 inch rack 263
- 1 Lift handle 3 Power cord 277
- Removing slot blanks 284
- # conf t 285
- # set-fan-speed auto 285
- 1Interface module 286
- Figure 198 302
- Figure 200 304
- Figure 202 306
- 4ALM 9Power supply 309
- 1Lug screws 2 Power lug (2) 312
- Cable cinch overview 321
- FIGURE 212 Two mRJ21 cables 322
- FIGURE 213 Three mRJ21 cables 322
- FIGURE 215 Five mRJ21 cables 323
- FIGURE 216 Six mRJ21 cables 324
- FIGURE 217 Seven mRJ21 cables 324
- RJ45 procedures 325
- 12 RJ45 cables in two groups 326
- 24 RJ45 cables in four groups 327
- 30 RJ45 cables in five groups 327
- 36 RJ45 cables in six groups 328
- Assigning permanent passwords 331
- Configuring IP addresses 332
- Support of subnet masks 333
- LED Desired 337
- Meaning Abnormal 337
- Meaning or action 337
- Testing network connectivity 338
- Managing Routers and Modules 339
- • Status of the fans 342
- • MAC address of the device 342
- Managing the device 343
- Field Description 345
- Static and dynamic buffers 346
- Managing the cooling system 349
- • LP – An interface module 353
- Monitoring the cooling system 354
- Temperature log reduction 355
- Managing interface modules 356
- Brocade# lp sync all 357
- Changing the boot source 358
- Displaying CPU usage 364
- Removing MAC address entries 366
- Hardware maintenance schedule 367
- Replacing a management module 368
- Replacing an interface module 369
- Replacing a power supply 372
- 5Latch handle open 376
- Replacing fan assemblies 377
- 1 Fan module 1 6 Fan module 6 379
- 2 Fan module 2 7 Fan module 7 379
- 3 Fan module 3 8 Fan module 8 379
- 4 Fan module 4 9 Fan module 9 379
- Replacing the air filters 385
- 1Captive screws 386
- • Phillips screwdriver 391
- • Small flathead screwdriver 391
- • ESD wrist strap 391
- FIGURE 250 Handle removal 394
- Hardware Specifications 397
- Component Maximum power 398
- Physical dimensions 400
- Operating environment 400
- Storage environment 400
- Safety agency approvals 400
- Electromagnetic approvals 400
- Power specifications 402
- Console port pin assignments 408
- Power cords 410
- Brocade MLXe Chassis bundles 413
- Regulatory Statements 427
- Power cords (Japan Denan) 429
- TABLE 73 Anatel certificates 431
- Caution and Danger Notices 433
- Cautions 434
Verwandte Produkte und Handbücher für Hardware Brocade-communications-systems Brocade MLX Series and Brocade Netlron XMR 53-1002
(168 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern