Brocade Communications Systems Gateway Wartungshandbuch Seite 95
- Seite / 104
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Rejoining Fabric OS switches to a fabric
When a switch reboots after AG mode is disabled, the Default zone is set to no access. Therefore, the
switch does not immediately join the fabric to which it is connected. Use one of the following methods to
rejoin a switch to the fabric:
• If you saved a Fabric OS configuration before enabling AG mode, download the configuration using
the configDownload command.
• If you want to rejoin the switch to the fabric using the fabric configuration, use the following
procedure.
To rejoin the Fabric OS switch to a fabric, perform the following steps:
1. Connect to the switch and log in using an account assigned to the admin role.
2. Enter the switchDisable command to disable the switch.
3. Enter the defZone --allAccess command to allow the switch to merge with the fabric.
4. Enter the cfgSave command to commit the Default zone changes.
5. Enter the switchEnable command to enable the switch and allow it to merge with the fabric.
The switch automatically rejoins the fabric.
Reverting to a previous configuration
1. Connect to the switch and log in using an account assigned to the admin role.
2. Enter the switchDisable command to disable the switch.
3. Enter the configDownload command to revert to the previous configuration.
4. Enter the switchEnable command to bring the switch back online.
The switch automatically joins the fabric.
Rejoining Fabric OS switches to a fabric
Access Gateway Administrator's Guide 95
53-1003126-02
- Access Gateway 1
- Contents 3
- Document conventions 7
- Notes, cautions, and warnings 8
- Brocade resources 9
- Document feedback 10
- About This Document 11
- Key terms for Access Gateway 12
- Access Gateway Basic Concepts 15
- Virtual Fabrics support 21
- Device authentication support 21
- Supported Fabric OS commands 22
- Password distribution support 23
- Access Gateway port types 24
- Port state description 28
- Access Gateway mapping 29
- Default port mapping 30
- Adding F_Ports to an N_Port 35
- F_Port Static Mapping 36
- Device mapping 37
- Static versus dynamic mapping 40
- Device mapping to N_Ports 42
- Disabling device mapping 42
- Enabling device mapping 43
- Pre-provisioning 43
- Configuring device mapping 44
- Mapping priority 45
- Device mapping considerations 45
- N_Port configurations 46
- Unlocking N_Ports 47
- Persisting port online state 47
- D_Port support 48
- Saving port mappings 49
- Displaying current policies 51
- How the ADS policy works 52
- Allow lists 53
- ADS policy considerations 55
- How the APC policy works 55
- Port Grouping policy 56
- How port groups work 57
- Removing a port group 58
- Renaming a port group 59
- Port Grouping policy modes 59
- Rebalancing F_Ports 60
- Enabling MFNM mode 61
- Disabling MFNM mode 61
- Device Load Balancing policy 62
- Persistent ALPA policy 63
- Persistent ALPA device data 64
- Failover policy 65
- Failover with port mapping 66
- FIGURE 11 Failover behavior 67
- Failover with device mapping 69
- Failback policy 71
- Failback example 72
- FIGURE 12 Failback behavior 73
- How trunking works 75
- Trunk group creation 76
- Setting up trunking 76
- Trunk area assignment example 76
- Assigning a trunk area 76
- Enabling trunking 77
- Disabling F_Port trunking 78
- Monitoring trunking 78
- QoS: Ingress rate limiting 82
- Per-Port NPIV login limit 84
- Performance Monitoring 85
- End-to-end monitors 86
- Frame monitors 86
- Direct target attachment 89
- Target aggregation 91
- Access Gateway cascading 92
- Verifying the switch mode 93
- Connectivity to Cisco fabrics 94
- Troubleshooting 97
- 53-1003126-02 100
Verwandte Produkte und Handbücher für Gateways / Controller Brocade Communications Systems Gateway
(62 Seiten)Canon FAX-JX210 manuals
Owner’s manuals and user’s guides for DVD players Canon FAX-JX210.
We providing pdf manuals Canon FAX-JX210 for download free by document types:
Kommentare zu diesen Handbüchern